約 3,146,308 件
https://w.atwiki.jp/anthony/pages/27.html
玄箱PROパッチ適用 私のようにswat不具合を抱えた玄箱PROを持っている場合は必要になる作業です。ここではTFTPを使用したパッチ適用（ファームウェア・バージョンアップ）です。これもシリアルコンソールなしにはできません。 TFTPサーバー Poor TFTP Server for WIN32をダウンロードして展開 ptftp32.exeを実行 Timeoutは60秒に設定しておく 同じディレクトリにinitrd.buffaloとuImage.buffaloを配置しておく シリアルコンソールからリブートする KUROBOX-PRO ~# reboot PCのアドレスが192.168.1.4でさっき玄箱PROをブートしたときのアドレスが192.168.1.12だったのでserveripにはPCのアドレス、ipaddrには玄箱PROのアドレスを設定 Marvell setenv serverip 192.168.1.4 Marvell setenv ipaddr 192.168.1.12 Marvell tftp $(default_kernel_addr) $(kernel) Using egiga0 device TFTP from server 192.168.1.4; our IP address is 192.168.1.12 Filename uImage.buffalo . Load address 0x100000 Loading ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### done Bytes transferred = 1736612 (1a7fa4 hex) Marvell setenv bootargs $(bootargs_base) $(bootargs_root) rw initrd=0x02000040,20M panic=5 $(buffalo_ver) Marvell bootm $(default_kernel_addr) $(default_initrd_addr) stop_sound ## Booting image at 00100000 ... Image Name Linux-2.6.12.6-arm1 Created 2007-04-10 13 45 13 UTC Image Type ARM Linux Kernel Image (uncompressed) Data Size 1736548 Bytes = 1.7 MB Load Address 00008000 Entry Point 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02000000 ... Image Name initrd Created 2007-04-10 13 46 52 UTC Image Type ARM Linux RAMDisk Image (gzip compressed) Data Size 19286692 Bytes = 18.4 MB Load Address 00000000 Entry Point 00000000 Verifying Checksum ... Bad Data CRC bootm fail. system_not_found Using egiga0 device TFTP from server 192.168.1.4; our IP address is 192.168.1.12 Filename uImage.buffalo . Load address 0x100000 Loading ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### done Bytes transferred = 1736612 (1a7fa4 hex) Using egiga0 device TFTP from server 192.168.1.4; our IP address is 192.168.1.12 Filename initrd.buffalo . Load address 0x2000000 Loading ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################## done Bytes transferred = 19286756 (1264ae4 hex) stop_sound ## Booting image at 00100000 ... Image Name Linux-2.6.12.6-arm1 Created 2007-04-10 13 45 13 UTC Image Type ARM Linux Kernel Image (uncompressed) Data Size 1736548 Bytes = 1.7 MB Load Address 00008000 Entry Point 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02000000 ... Image Name initrd Created 2007-04-10 13 46 52 UTC Image Type ARM Linux RAMDisk Image (gzip compressed) Data Size 19286692 Bytes = 18.4 MB Load Address 00000000 Entry Point 00000000 Verifying Checksum ... OK Starting kernel ... arg console=ttyS0,115200 root=/dev/sda2 rw panic=5 rw initrd=0x02000040,20M panic=5 BOOTVER=1.091 CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX --- Uncompressing Linux........................................................ ......................................................... done, booting the kernel. Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #27 Tue Apr 10 22 47 16 JST 2007 CPU ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ) CPU0 D VIVT write-back cache CPU0 I cache 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0 D cache 32768 bytes, associativity 1, 32 byte lines, 1024 sets Machine MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 250000000, Tclk = 166664740 Memory policy ECC disabled, Data cache writeback Built 1 zonelists Kernel command line console=ttyS0,115200 root=/dev/sda2 rw panic=5 rw initrd=0x02000040,20M panic=5 BOOTVER=1.091 PID hash table entries 1024 (order 10, 16384 bytes) Console colour dummy device 80x30 Dentry cache hash table entries 32768 (order 5, 131072 bytes) Inode-cache hash table entries 16384 (order 4, 65536 bytes) Memory 128MB 0MB 0MB 0MB = 128MB total Memory 105600KB available (3037K code, 426K data, 112K init) Mount-cache hash table entries 512 CPU Testing write buffer coherency ok checking if image is initramfs...it isn t (no cpio magic); looks like an initrd Freeing initrd memory 20480K NET Registered protocol family 16 serial_initialize_ttyS1 (Debug) ttyS1 is initialized. config_device_cs Error Unknown board CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 128MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PCI0_MEM ....base e8000000, size 128MB PCI0_IO ....base f2100000, size 1MB INTER_REGS ....base f1000000, size 1MB DEVICE_CS0 ....base fa000000, size 2MB DEVICE_CS1 ....base f4000000, size 32MB DEVICE_CS2 ....base fa800000, size 1MB DEV_BOOCS ....base ff800000, size 8MB CRYPTO ENG ....no such Flash bankwidth 1, base ff800000, size 400000 KUROBOX FLASH size 4096[KB] Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_ BOARD_KUROBOX Soc 88F5182 A2 Detected Tclk 166664740 and SysClk 250000000 Marvell USB EHCI Host controller #0 c3403bc0 Marvell USB EHCI Host controller #1 c3403a40 pexBarOverlapDetect winNum 2 overlap current 0 mvPexInit Warning Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI bus0 Fast back to back transfers enabled PCI bus1 Fast back to back transfers enabled SCSI subsystem initialized usbcore registered new driver usbfs usbcore registered new driver hub Use the XOR engines (offloading) for enhancing the following functions o RAID 5 Xor calculation o kernel memcpy o kenrel memzero o copy user to/from kernel buffers Number of XOR engines to use 2 cesadev_init(c00122e4) Fast Floating Point Emulator V0.9 (c) Peter Teichmann. inotify device minor=63 JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. SGI XFS with no debug enabled Serial 8250/16550 driver $Revision 1.90 $ 4 ports, IRQ sharing disabled ttyS0 at MMIO 0x0 (irq = 3) is a 16550A ttyS1 at MMIO 0x0 (irq = 4) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized 3 RAM disks of 32768K size 1024 blocksize loop loaded (max 8 devices) Marvell Gigabit Ethernet Driver egiga o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface ** egiga_init_module (10) eth0 Intergrated Sata device found scsi0 Marvell SCSI to SATA adapter scsi1 Marvell SCSI to SATA adapter Vendor Hitachi Model HDT725050VLA360 Rev V56O Type Direct-Access ANSI SCSI revision 03 SCSI device sda 976773168 512-byte hdwr sectors (500108 MB) SCSI device sda drive cache write back SCSI device sda 976773168 512-byte hdwr sectors (500108 MB) SCSI device sda drive cache write back sda sda1 sda2 sda3 sda4 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 physmap flash device 400000 at ff800000 Found SST 39LF020 phys_mapped_flash Found 1 x8 devices at 0x0 in 8-bit bank number of JEDEC chips 1 cfi_cmdset_0002 Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Debug nand_scan nand_flash_ids[i].pagesize is exist Debug nand_scan mtd- erasesize=0x00020000 Debug nand_scan mtd- oobblock=0x00000800 Debug nand_scan mtd- oobsize=0x00000040 NAND device Manufacturer ID 0x20, Chip ID 0xda (ST Micro NAND 256MiB 3,3 V 8-bit) Scanning device for bad blocks Bad eraseblock 854 at 0x06ac0000 Using static partition definition Creating 3 MTD partitions on "nand_mtd" 0x00000000-0x00400000 "uImage" 0x00400000-0x04400000 "rootfs" 0x04400000-0x10000000 "extra" usbmon debugs is not available ehci_platform ehci_platform.4523 EHCI Host Controller ehci_platform ehci_platform.4523 new USB bus registered, assigned bus numb er 1 ehci_platform ehci_platform.4523 irq 17, io mem 0x00000000 ehci_platform ehci_platform.4523 park 0 ehci_platform ehci_platform.4523 USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0 1.0 USB hub found hub 1-0 1.0 1 port detected ehci_platform ehci_platform.16781 EHCI Host Controller ehci_platform ehci_platform.16781 new USB bus registered, assigned bus num ber 2 ehci_platform ehci_platform.16781 irq 12, io mem 0x00000000 ehci_platform ehci_platform.16781 park 0 ehci_platform ehci_platform.16781 USB 0.0 initialized, EHCI 1.00, driver 1 0 Dec 2004 hub 2-0 1.0 USB hub found hub 2-0 1.0 1 port detected USB Universal Host Controller Interface driver v2.2 Initializing USB Mass Storage driver... usbcore registered new driver usb-storage USB Mass Storage support registered. usbcore registered new driver usbhid drivers/usb/input/hid-core.c v2.01 USB HID core driver mice PS/2 mouse device common for all mice md raid0 personality registered as nr 2 md raid1 personality registered as nr 3 md raid5 personality registered as nr 4 raid5 measuring checksumming speed arm4regs 308.800 MB/sec 8regs 217.600 MB/sec 32regs 252.400 MB/sec raid5 using function arm4regs (308.800 MB/sec) md md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 Buffalo Platform Linux Driver(Light) 0.01 installed. MICON ctrl (C) BUFFALO INC. V.1.00 installed. Kernel event proc (C) BUFFALO INC. V.1.00 installed. MICON V2 (C) BUFFALO INC. V.1.00 installed. NET Registered protocol family 2 IP routing cache hash table of 1024 buckets, 8Kbytes TCP established hash table entries 8192 (order 4, 65536 bytes) TCP bind hash table entries 8192 (order 3, 32768 bytes) TCP Hash tables configured (established 8192 bind 8192) NET Registered protocol family 1 NET Registered protocol family 17 md Autodetecting RAID arrays. md autorun ... md ... autorun DONE. RAMDISK Compressed image found at block 0 VFS Mounted root (ext2 filesystem). ---- in linuxrc --- proc mount success libbuffalo mount success -RamdiskRoot- -- linuxrc finished. -- Freeing init memory 112K init started BusyBox v1.2.2 (2007.01.15-11 18+0000) multi-call binary Starting pid 242, console /dev/ttyS0 /etc/init.d/rcS --- rcStart (initrd) --- ===== Starting MountSystemFolders ===== mounting procfs ... [Success] mounting sysfs ... [Success] remounting rootfs ... [Success] mounting all devices ... [Success] --MountNandDevice-- ===== Starting Kevent.sh ===== [Success] ===== Starting networking.sh ===== Deconfiguration network interface lo eth0 killall dhcpcd no process killed create network files.. IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[] killall dhcpcd no process killed route SIOC[ADD|DEL]RT No such process Configuration network interface lo eth0 requesting DHCP tout=30[s] eth0 link down eth0 link up 5 , full duplex 5 , speed 100 Mbps 5 /etc/dhcpc/dhcpcd.exe /etc/dhcpc/dhcpcd-eth0.info new dhcpcd.exe interface eth0 has been configured with new IP=192.168.1.12 hostname is setted to KUROBOX-PRO [Success] ===== Starting sethostname.sh ===== hostname is setted to KUROBOX-PRO [Success] ===== Starting clientUtil_servd.sh ===== Starting clientUtil_server starting on eth0 start at debug mode clientUtil_server Ver.1.01 listen device name = eth0 [Success] Starting pid 484, console /dev/ttyS0 /sbin/getty KUROBOX-PRO login } ログインして更新コマンドを実行する実行 ~ # update_mtd.sh all ***** Cleaning and collect badlist /dev/mtd1 ***** ***** copying /boot/uImage.buffalo to /dev/mtd1 ***** ***** Cleaning /dev/mtdchar2 ***** ***** Writing /boot/nandrootfs.jffs2 to /dev/mtdchar2 ***** ***** copying /boot/u-boot.bin to /dev/mtd0 ***** 480+1 records in 480+1 records out ***** Cleaning /dev/mtdchar3 ***** Done. ~ # リブートする ~ # reboot Orion1 CPU = Low === KURO U-Boot. === ** LOADER ** ** KUROBOX BOARD KURO_BOX LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Apr 10 2007 - 18 10 08) Marvell version 1.12.1 - TINY DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] Flash 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M) Done NAND 256 MB Soc 88F5182 A2 CPU ARM926 (Rev 0) running @ 500Mhz Orion 1 streaming disabled SysClock = 250Mhz , TClock = 166Mhz USB 0 host mode USB 1 host mode PCI 0 PCI Express Root Complex Interface PCI 1 Conventional PCI, speed = 33000000 Net egiga0 [PRIME] Using 88E1118 phy Found boot image hit any key to switch tftp boot. Hit any key to stop autoboot 0 system_bootend Hit any key to stop autoboot 0 Loading from device 0 NULL at 0xfa000000 (offset 0x20000) Image Name Linux-2.6.12.6-arm1 Created 2007-04-10 13 45 13 UTC Image Type ARM Linux Kernel Image (uncompressed) Data Size 1736548 Bytes = 1.7 MB Load Address 00008000 Entry Point 00008000 stop_sound ## Booting image at 00100000 ... Image Name Linux-2.6.12.6-arm1 Created 2007-04-10 13 45 13 UTC Image Type ARM Linux Kernel Image (uncompressed) Data Size 1736548 Bytes = 1.7 MB Load Address 00008000 Entry Point 00008000 Verifying Checksum ... OK OK Starting kernel ... arg console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.091 CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX --- Uncompressing Linux........................................................ ......................................................... done, booting the kernel. Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (C odeSourcery ARM 2005q3-2)) #27 Tue Apr 10 22 47 16 JST 2007 CPU ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ) CPU0 D VIVT write-back cache CPU0 I cache 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0 D cache 32768 bytes, associativity 1, 32 byte lines, 1024 sets Machine MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 250000000, Tclk = 166664740 Memory policy ECC disabled, Data cache writeback Built 1 zonelists Kernel command line console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BO OTVER=1.091 PID hash table entries 1024 (order 10, 16384 bytes) Console colour dummy device 80x30 Dentry cache hash table entries 32768 (order 5, 131072 bytes) Inode-cache hash table entries 16384 (order 4, 65536 bytes) Memory 128MB 0MB 0MB 0MB = 128MB total Memory 126208KB available (3037K code, 426K data, 112K init) Mount-cache hash table entries 512 CPU Testing write buffer coherency ok NET Registered protocol family 16 serial_initialize_ttyS1 (Debug) ttyS1 is initialized. config_device_cs Error Unknown board CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 128MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PCI0_MEM ....base e8000000, size 128MB PCI0_IO ....base f2100000, size 1MB INTER_REGS ....base f1000000, size 1MB DEVICE_CS0 ....base fa000000, size 2MB DEVICE_CS1 ....base f4000000, size 32MB DEVICE_CS2 ....base fa800000, size 1MB DEV_BOOCS ....base ff800000, size 8MB CRYPTO ENG ....no such Flash bankwidth 1, base ff800000, size 400000 KUROBOX FLASH size 4096[KB] Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BO ARD_KUROBOX Soc 88F5182 A2 Detected Tclk 166664740 and SysClk 250000000 Marvell USB EHCI Host controller #0 c04e4b00 Marvell USB EHCI Host controller #1 c04e4a40 pexBarOverlapDetect winNum 2 overlap current 0 mvPexInit Warning Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI bus0 Fast back to back transfers enabled PCI bus1 Fast back to back transfers enabled SCSI subsystem initialized usbcore registered new driver usbfs usbcore registered new driver hub Use the XOR engines (offloading) for enhancing the following functions o RAID 5 Xor calculation o kernel memcpy o kenrel memzero o copy user to/from kernel buffers Number of XOR engines to use 2 cesadev_init(c00122e4) Fast Floating Point Emulator V0.9 (c) Peter Teichmann. inotify device minor=63 JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. SGI XFS with no debug enabled Serial 8250/16550 driver $Revision 1.90 $ 4 ports, IRQ sharing disabled ttyS0 at MMIO 0x0 (irq = 3) is a 16550A ttyS1 at MMIO 0x0 (irq = 4) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized 3 RAM disks of 32768K size 1024 blocksize loop loaded (max 8 devices) Marvell Gigabit Ethernet Driver egiga o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface ** egiga_init_module (10) eth0 Intergrated Sata device found scsi0 Marvell SCSI to SATA adapter scsi1 Marvell SCSI to SATA adapter Vendor Hitachi Model HDT725050VLA360 Rev V56O Type Direct-Access ANSI SCSI revision 03 SCSI device sda 976773168 512-byte hdwr sectors (500108 MB) SCSI device sda drive cache write back SCSI device sda 976773168 512-byte hdwr sectors (500108 MB) SCSI device sda drive cache write back sda sda1 sda2 sda3 sda4 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 physmap flash device 400000 at ff800000 Found SST 39LF020 phys_mapped_flash Found 1 x8 devices at 0x0 in 8-bit bank number of JEDEC chips 1 cfi_cmdset_0002 Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Debug nand_scan nand_flash_ids[i].pagesize is exist Debug nand_scan mtd- erasesize=0x00020000 Debug nand_scan mtd- oobblock=0x00000800 Debug nand_scan mtd- oobsize=0x00000040 NAND device Manufacturer ID 0x20, Chip ID 0xda (ST Micro NAND 256MiB 3,3 V 8-bit) Scanning device for bad blocks Bad eraseblock 854 at 0x06ac0000 Using static partition definition Creating 3 MTD partitions on "nand_mtd" 0x00000000-0x00400000 "uImage" 0x00400000-0x04400000 "rootfs" 0x04400000-0x10000000 "extra" usbmon debugs is not available ehci_platform ehci_platform.4523 EHCI Host Controller ehci_platform ehci_platform.4523 new USB bus registered, assigned bus numb er 1 ehci_platform ehci_platform.4523 irq 17, io mem 0x00000000 ehci_platform ehci_platform.4523 park 0 ehci_platform ehci_platform.4523 USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0 1.0 USB hub found hub 1-0 1.0 1 port detected ehci_platform ehci_platform.16781 EHCI Host Controller ehci_platform ehci_platform.16781 new USB bus registered, assigned bus num ber 2 ehci_platform ehci_platform.16781 irq 12, io mem 0x00000000 ehci_platform ehci_platform.16781 park 0 ehci_platform ehci_platform.16781 USB 0.0 initialized, EHCI 1.00, driver 1 0 Dec 2004 hub 2-0 1.0 USB hub found hub 2-0 1.0 1 port detected USB Universal Host Controller Interface driver v2.2 Initializing USB Mass Storage driver... usbcore registered new driver usb-storage USB Mass Storage support registered. usbcore registered new driver usbhid drivers/usb/input/hid-core.c v2.01 USB HID core driver mice PS/2 mouse device common for all mice md raid0 personality registered as nr 2 md raid1 personality registered as nr 3 md raid5 personality registered as nr 4 raid5 measuring checksumming speed arm4regs 304.000 MB/sec 8regs 215.200 MB/sec 32regs 249.200 MB/sec raid5 using function arm4regs (304.000 MB/sec) md md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 Buffalo Platform Linux Driver(Light) 0.01 installed. MICON ctrl (C) BUFFALO INC. V.1.00 installed. Kernel event proc (C) BUFFALO INC. V.1.00 installed. MICON V2 (C) BUFFALO INC. V.1.00 installed. NET Registered protocol family 2 IP routing cache hash table of 1024 buckets, 8Kbytes TCP established hash table entries 8192 (order 4, 65536 bytes) TCP bind hash table entries 8192 (order 3, 32768 bytes) TCP Hash tables configured (established 8192 bind 8192) NET Registered protocol family 1 NET Registered protocol family 17 md Autodetecting RAID arrays. md autorun ... md ... autorun DONE. Empty flash at 0x00df85f8 ends at 0x00df8800 VFS Mounted root (jffs2 filesystem). Freeing init memory 112K --- rcStart (NANDroot) --- ===== Starting MountSystemFolders ===== mounting procfs ... [Success] mounting sysfs ... [Success] mouting usbfs ... [Success] remouting rootfs ... [Success] mounting all devices ... [Success] ===== Starting checkroot.sh ===== rm /var/lock/perfmon is a directory rm /var/lock/printing is a directory rm /var/lock/subsys is a directory [Success] ===== Starting Kevent.sh ===== [Success] ===== Starting mount_share.sh ===== Mounting /dev/sda4 on /mnt/disk1 as a xfs file system. XFS mounting filesystem sda4 Starting XFS recovery on filesystem sda4 (dev sda4) Ending XFS recovery on filesystem sda4 (dev sda4) Success. Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system. Success. [Success] ===== Starting sethostname.sh ===== hostname is setted to KUROBOX-PRO [Success] ===== Starting networking.sh ===== create network files.. IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[] killall dhcpcd no process killed route SIOC[ADD|DEL]RT No such process Configuration network interface lo eth0 requesting DHCP tout=30[s] eth0 link down eth0 link up 5 , full duplex 5 , speed 100 Mbps 5 /etc/dhcpc/dhcpcd.exe /etc/dhcpc/dhcpcd-eth0.info up dhcpcd.exe interface eth0 has been configured with old IP=192.168.1.12 hostname is setted to KUROBOX-PRO [Success] ===== Starting httpd.sh ===== [Success] ===== Starting telnet.sh ===== [Success] ===== Starting inetd.sh ===== [Success] ===== Starting smb.sh ===== $Starting SMB services $Starting NMB services [Success] ===== Starting clientUtil_servd.sh ===== Starting clientUtil_server starting on eth0 [Success] ===== Starting bootcomplete.sh ===== [Success] ===== Starting FanController.sh ===== [Success] ===== Starting boss.sh ===== ... .. -~~(~~ .~ shDBDhz+(-. .~+sDDBNBDhhszDBNNNNBNNNBDs - ~sBNNNNNNNNNNNNNNNNNNNNNNNNNBs -=DNNBNNNNNNNNNNNNNNNNNBNNNNNNNNBz .~zNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNz~ ~hBNNNNBNNNNNNNNNNNNNNNNNNNNNNNNNNNNNND+ (hNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNBs- .~zNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNBNNBNNNNNNBs ~sBNNNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNNNNNNNz (+DNNNNNNNNNNNNNNNNNNNNNNDzNNNNNhzDNNBNNNNNNNNBs (sNNNNNNNNNNNNNNNNNNNNNNB=~hNNNN=~(sDNNNNNNNNNND (+DNNNNNNNNNNNNNNNNNNNNNNs .=NNNNz- (zDNNNNNNNNNz ~=BNNNNNNNNNNNNNNNNNNNNND- .=BNNNN . .(hNNNNNNNNB ~sNNNNNNNNNNNNNNNNNNNNND+. .+BNNNN+ ~sBNNNNNNN (zNNNNNNNNNNNNNNNNNNNNND ..+BNBNB=- .+BNNNNNNh (zNNNNNNNNNNNNNNNNNNNBB= . hNBBNs+- +DNNNBND (sNNNNNNNNNNNNNNNNNNNND( -DhDBN+ - . =NNNNNB ~+DNNBNNNNNNNNNNNNNNNNz =D=Dhh+( . ~DBNNNB ~(sNNNNNNNNNNNNNNNNNNNz. -hs(zz+ ( . .=NNNNN ~=NNBBBBNNNNNNNNNNNNB= ==-=+s((~. .~BNNNB ~=Nhs +++hNNNNNNNNBz - .~=-.s(+-(- hBNND =Ds+hz( ~hNNNNNNND+ ..-+ .-((( ~ ... -hNNNNDs ~+z(BN=. . BNNNNBhhDD=+ ~. ~-=shBBDhz+( -sBNNNBBNBz ~(=z(BD- ~~hBNNNs~-( zDDs+~(shzssszDBNDh= sBNNNNNNNBN ~~+s z=.-zh~sNNND . . zhhh==shDBNNNNNNNBDDNNNNNNNNNh ~~ ss+ .zBBs~zND+ ..-+zDBNNNNNNNNNNNhzNNNNNNNNND+ ~~(=h +DBz-sBs~ . (BBNNNNNNNNNz- BBNNBNNND= ~(~ zss(( (z sD+ ~DNNNNNNNNNz~ sNNNNNNDs ~(=Ds= ...-(h . . .. BNNNNNNNNz~ -hNNNBh ~(hNs(. =- .=BNNNNNBNs- .(hs== BNz~ . .(hBNNBDz .~ - -hNNh(. .. . (++~ . - . hBNB+ -+( . .- . zDNz( . ~+ - .. . .-. ..~(-. . . .~+(. .. -- . . . + ~ ~. ..... .- . ---(~~~( ~. .. . .((--- -~~(~ . . +s=(- -(+. Let s start a KURO-BOX! .... .(hBDzDD=. and have a fun time... .. .. . sDh+. . .. . ..-- . .. .. ... ....... . . .. .. - .. ... [Success] KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO) KUROBOX-PRO login 最終更新日：2007-05-28
https://w.atwiki.jp/aerocats/pages/41.html
NASとはNetwork Attached Storageの略で「ネットワーク接続ストレージ」と訳され「ネットワーク上の保存装置」という意味だ。 コンピューターに接続された外付けHDDは、接続元のコンピューターの電源が入っていないと扱えないがNASは独立した機器なので同一ネットワーク内であればどこからでも使える利点がある。 基本的にはコントローラー部分とHDDをあわせたものをNASと呼ぶ。 玄箱PROは初期状態でこれらの機能を有している。
https://w.atwiki.jp/zakouji/pages/31.html
個人的 覚書 ■ ライブCDの部屋 ■ Dream Linux 2.2 DL 3D表示が出来る Vista並のオモチャ。 ■ Debian 2種(xFce版, カスタマイズ版) DL Debian系ブラウザ Iceweasel（アイス ウィーズル = 氷のイタチ）の表示が変 何でも Iceにするな！！ 我が core7の php.phpを DLしようとする。 ■ SLAMPP 1.1 参考 ブログ 本家は死亡？ xfec, Apache 1.3.34, PHP 4.4.1, firefox1.5 それぞれ自分で かなりのアップデート, インストールしなくちゃならない。 カメレオンでも無く ゲッコでも無い 砂漠トカゲの壁紙・・・インターネット創世記への回帰？ それとも Su？？？？(^^; rootでログイン後 xstart, ブラウザで サーバー設定可 info.phpも ローカルサーバーでデフォルト表示 mntに hda他, サンバも正常動作している模様, fedoraを見るには imgをマウントする？ ■ SLAMPP Lite 2.0 英語 参考ページ Apacheはそのまま？ 本家が行方不明 他 1CDサーバー(220M) LAMPPIX 1.1 ■ 日本語 DSLも有った。 本家 07/03に v3.4になっているので 少し待ってみる。 ・・・って、もう 27日じゃねーかっ！無駄かな？・・・ 発売前の Vistaに 日本語 qemu + 英語 DSLで遊んだけど 設定等 細かな事 忘れた。 486, メモリー16Mでも動作可・・・我が家には 286どころか z80, z86が有る・・・ そう言えば i386なんてフォルダー有っても 386で動作させてみろっ！！って感じの Windowsや Linux もう CPUが 686でないと インストール出来ない ディストリビューションも有るつうの。 ■ Berry 0.82 Fedora 7 ベースに変更。 Firefoxが 1.5のまま。 漢字変換も嫌い。 Core 6から Fedoraに LiveCDが有るから・・・もう再構築して配る 意味が無いんじゃないか？ Revisorで カスタマイズした LiveCDも作成出きるんだし・・・ ■ not Core 7 simpleapi_img ■ Fedora Link ├ オフィシャルJP ├ オフィシャルLiveCD ├ オフィシャルBittorennt ├ オフィシャルmirror ├ FedoraBBSJapan └ 個人的ノート ■ Linux Link ├ 日本のLinux情報 ├ 朱の鳥 ├ ペンギンの杜 ├ UNIXな生活 ├ ライブCD └ DSL .
https://w.atwiki.jp/aerocats/pages/25.html
wgetコマンド?の際、玄箱PROが外部と未接続の場合に発生する。
https://w.atwiki.jp/aerocats/pages/63.html
/varとは /varの構成 標準Linuxのvarディレクトリは/mnt/ram/varのシンボリックリンクとなっている。 つまりRAM上に作られているため、玄箱PROの電源を切るたびに内容は消えてしまうということだ。 実際に標準Linuxではどのような構成となっているか。 ファイルもしくはディレクトリ名 設定内容 empty lib lock log run spool tmp
https://w.atwiki.jp/unturned/pages/485.html
データ #ref error ：ご指定のファイルが見つかりません。ファイル名を確認して、再度指定してください。 (Fedora.png) 種別 衣類 占有マス(縦×横) 2×2 スタック 不可能 ゲーム内説明 Hipster head embelishment. 流行に敏感な人が頭につけるもの 概要 フェドーラ。ソフト帽。折り目を付けられた冠のあるフェルトから作られた帽子。 このアイテムを使うレシピ Apparel 出来るもの 材料1 材料2 必要な道具 必要スキル Cloth x 2(布) Fedora x 1(ソフト帽) - - - 衣類 胴体 一般 Blue Sweatervest / Suit / Orange Hoodie / Pink Shirt ベスト Poncho / Magick Cloak アーマー Civilian Armor 頭 帽子 Bandana / Shades / Beret / Ushanka / White Hat ヘルメット Miner Helmet ヘッドギア Civilian NVG / Military NVG 足 Jeans / Brown Pants / Khaki Pants / Grey Pants セット 軍隊 （Forest系）Forest Fatigues（Top) / Forest Fatigues(Bottom) / Forest Armor / Forest Helmet（Desert系）Desert Fatigues(Top) / Desert Fatigues(Bottom) / Desert Armor / Desert Helmet 警察 Police Uniform(Top) / Police Cap / Police Uniform(Bottom) / Police Armor 消防士 Fire Helmet（黄）Fireperson Top(Yellow) / Fireperson Pants(Yellow)（黒）Fireperson Top(Black) / Fireperson Pants(Black) シェフ Chef Shirt / Chef Hat / Chef Pants ギリースーツ Ghillie Top / Ghillie Hood / Ghillie Pants RCMP RCMP Uniform(Top) / RCMP Uniform(Bottom) / Stetson 忍者 Ninja Top / Ninja Hood / Ninja Bottom 水兵 Sailor Fatigues(Top) / Sailor Fatigues(Bottom) / Dixie Hat 医者 Doctor Coat / Doctor Pants 作業員 Construction Vest / Construction Helmet / Work Jeans 商人 Grocer Top / Grocer Bottom 木こり Plaid Shirt / Lumberjack Pants 農家 Jumper Top / Jumper Bottom / Farmer Hat スーツ Boring Suit / Boring Pants アニマル Animal Shirt / Animal Pants ゴールド Fancy Suit / Fancy Jeans / Fancy Shades
https://w.atwiki.jp/kimh/pages/27.html
Fedora 自宅サーバー
https://w.atwiki.jp/w124/pages/14.html
@fedora12に関する情報 これ以外のプラグインについては@wikiガイドをご覧ください = http //atwiki.jp/guide/
https://w.atwiki.jp/chaos987/pages/25.html
Fedora 15 のインストールには最低でも 640MiB 以上のメモリが必要。 512MiB だとインストーラが起動できない（text モードでも）。 yum を使えば 512M でも 14 = 15 に一応アップグレードできる（保証はできないが）。 Upgrading Fedora using yumを参照。 rpm --import https //fedoraproject.org/static/069C8460.txt yum update yum yum clean all yum --releasever=15 --disableplugin=presto distro-sync 注：テキストモードで実行すること。 依存関係でエラーになるときは該当パッケージを削除する。 yum remove package GNOME を使っているならおそらく gnome-panel-libs がエラーになる。 編集 コメント 名前 コメント すべてのコメントを見る
https://w.atwiki.jp/sevenlives/pages/155.html
Spins オンライン・デスクトップ LiveCD LiveDVD Fedora Core6? Fedora7? Fedora8 Fedora9? Fedora10? Fedora11? Fedora12? Fedora13? Fedora14 Fedora15? ◎ ディレクトリ構造? /?root home?user? etc